What does a furnace tune-up in Toronto include?
Best HVAC Toronto is a family-owned, TSSA-certified HVAC contractor serving Toronto and the Greater Toronto Area, with over 20 years of combined Ontario HVAC crew experience. Our annual furnace tune-up is a structured furnace maintenance visit covering every component that affects safety, combustion efficiency, and reliability through the heating season. We schedule the majority of our fall tune-ups between August and October, when demand for heating has not yet peaked, so you can secure an appointment quickly and your furnace is ready before the first cold snap.
The visit runs 60 to 90 minutes. Best HVAC Toronto’s certified technicians, each holding a TSSA G1 or G2 gas licence and covered by WSIB, work through a fixed checklist rather than a general walkthrough, so nothing is left to discretion or skipped under time pressure. Every finding, measurement, and completed cleaning step is recorded on a written service report you keep at the end of the visit.
The 8-point HVAC checklist we follow on every visit
Heat exchanger and secondary heat exchanger. We inspect the primary and secondary heat exchanger surfaces for cracks, corrosion, and deterioration. A cracked heat exchanger allows combustion gases to mix with the air circulating through your home, which is the same fault Enbridge issues red tags for. If anything looks borderline, the combustion analyzer reading helps confirm or rule out the concern rather than leaving it to a visual guess alone.
Combustion analysis. A calibrated combustion analyzer measures flue gas composition, CO levels in parts per million, flue temperature, and combustion efficiency. This is the only reliable way to confirm the furnace is burning cleanly and safely. The readings are recorded on your service document, which is useful for warranty claims and insurance purposes.
Blower motor and wheel. We measure blower motor amperage against the nameplate rating to catch a motor running hot before it fails mid-winter. The blower wheel is cleaned of lint and debris buildup, restoring airflow and improving system efficiency without any part replacement.
Gas pressure calibration. Manifold and supply gas pressure are checked with a manometer and set to the manufacturer’s specification, in line with the CSA B149.1 gas code that TSSA enforces across Ontario. Pressure drift over multiple heating seasons is a common cause of poor combustion readings and nuisance lockouts.
Safety switches and limit controls. The high-limit switch, rollout switch, and pressure switch are each tested for proper operation. A failing limit switch is one of the more common causes of furnace short-cycling and is frequently found on units that have gone without annual service.
Igniter and flame sensor. The hot surface igniter is inspected for hairline cracks. The flame sensor is cleaned to remove the oxidation layer that builds up over one or two heating seasons, which reduces the signal the furnace control board uses to confirm a stable flame and can cause repeated lockouts if left unaddressed.
Venting and draft. We check flue connections, venting integrity, and draft at the appliance to confirm combustion gases are leaving the building correctly. Blocked or corroded venting is one of the most common red tag causes in Toronto’s older housing stock, particularly in semi-detached homes in East York and York where a high-efficiency furnace was added years ago while the water heater remained on the chimney.
Filter inspection. We check filter condition and provide a recommendation on timing and filter grade. A standard 1-inch disposable filter that needs replacement is swapped during the visit. Media filters and whole-home filtration systems are assessed and quoted separately.
Why should you service your furnace every year?
Toronto winters push residential furnaces hard. Most systems run continuously from November through March, with overnight lows that regularly reach minus 15 Celsius or colder in a cold year. A furnace that starts the season with a dirty blower, a borderline igniter, or burners running off-spec may survive the winter, or it may fail during a cold stretch when no-heat calls stack up and same-day appointment availability tightens. Homes running a hybrid setup, where a cold-climate heat pump handles milder days, still rely on the gas furnace on the coldest nights, so the furnace side gets the same full checklist.
Annual maintenance also keeps your manufacturer warranty intact. Most manufacturers require documented annual service as a condition of coverage, and a gap in that record is grounds for a claim denial on a heat exchanger or blower motor. Our written service record is accepted by every brand we are authorized to service, including Lennox, Carrier, Trane, Bosch, Napoleon, and York. On ENERGY STAR-certified high-efficiency furnaces, which Natural Resources Canada rates by AFUE, a clean blower and calibrated burners keep the unit running close to the efficiency you paid for.
A clean combustion analysis gives you documented proof that your furnace is burning safely if an Enbridge meter reader or a home inspector questions the appliance condition. If the inspection turns up a needed furnace repair, our technicians carry the common parts on the van. Igniter replacements, flame sensor swaps, and pressure switch replacements are usually completed on the same visit. Larger repairs are quoted in writing before we proceed. If you need emergency service at any hour, our line is staffed 24/7 at 647-254-4113.
Booking fall maintenance across Toronto and the GTA
From post-war bungalows in Scarborough and Etobicoke to two-storey detached homes and townhouses in Vaughan, Markham, and Mississauga, the Best HVAC Toronto crew services furnaces across the full Greater Toronto Area. Annual furnace maintenance is also available in North York, East York, Brampton, Richmond Hill, Oakville, Burlington, and the Durham region including Ajax, Pickering, Whitby, and Oshawa.
Searching for a furnace tune-up near you? Fall slots fill quickly as homeowners schedule ahead of heating season, so we recommend booking in August or September to secure your preferred time. Tune-ups run $150 to $220 per visit at 2026 rates. For customers who schedule with us every year, repeat customer discounts apply automatically to the next visit. Maintenance plan members receive priority fall scheduling alongside the reduced member rate.
Book your annual furnace tune-up by calling 647-254-4113, Monday through Saturday from 7 AM to 8 PM, or request a booking online. Our 24/7 emergency line is available at the same number if your furnace needs attention before your scheduled visit.
